* [https://lujji.github.io/blog/stlink-clone-trace/ Trace support for ST-Link clones ]
.../quick-hack-to-get-swo-on-st-link-clones/ eevblog]. Turning st-link into j-link might require the following:
355 bytes (42 words) - 12:53, 21 January 2017
[[Rationale::This content bundle features a set of basic elements that are necessary for the
;This content bundle comprises a set of articles that are necessary to make use o
1 KB (194 words) - 22:23, 10 February 2013
...ansparent-esp8266-wifi-to-serial-bridge/ this hackaday page] points to esp-link, an esp8266 firmware dedicated to providing a transparent wifi-serial bridg
[http://www.esp8266.com/wiki/doku.php?id=esp8266-module-family This page] lists available esp8266 modules. I've got an esp-01 (and several esp-
1 KB (171 words) - 17:56, 1 January 2017
|style="width:64px;"|[[File:Ws2811 thumbnail.jpg|upright=1.0|link=Driving the WS2811 at 800 kHz with an 8 MHz AVR]]
...tring from an 8 Mhz AVR? [[Driving the WS2811 at 800 kHz with an 8 MHz AVR|This page]] has the code and explains it. Works for Arduino too...
6 KB (883 words) - 21:17, 19 November 2020
...be programmed too, so we've evolved several ways to program these as well. This page describes them.
disconnecting and reconnecting is quite a hassle with this and all in all this is not very stable.
5 KB (831 words) - 09:58, 16 November 2014
...formation on a serial port and periodically sends this data through an ftp-link to a central server.
...on [http://www.race-technology.com/wiki/index.php/General/SerialDataFormat this page].
1 KB (158 words) - 00:29, 8 December 2011
...n sx lst file, sets breakpoints and manipulates the state of the emulator. This can be used to simulate inputs or to log outputs of the SX while it is runn
...CD. After all is set up, the script will run the emulator for 100 Mclocks. This should continuously print an updated LCD display.
4 KB (714 words) - 22:07, 12 July 2010
...care (both installing and removing the board rarely happens by the way, so this is not a very big issue). I used slightly longer pins, but that might not e
...ead of a bare pin header. I used a 10-pin IDC programming header socket in this case, because the cheapest programmers seem to have 10-pin cables (and not
5 KB (869 words) - 09:28, 20 September 2013
This page will contain the notes that I will make during [http://www.boostcon.co
bjam --with-serialization --layout-system variant=debug link=shared stage
4 KB (566 words) - 22:07, 12 July 2010
...30'' version wherever a ''29'' version appears. You should be able to find this file in ''<cmake-install-dir>''\share\cmake-2.8\Modules.
# This module finds if wxWidgets is installed and selects a default
37 KB (4,594 words) - 20:42, 27 March 2014
...This page describes the design of the core emulator. The implementation of this emulator revolves around a few main ideas:
...iar with MP may want to look through some of the examples in the wikipedia link...
21 KB (3,146 words) - 14:56, 23 February 2013
This page describes how to drive a WS2811 from an 8Mhz or 9.6Mhz AVR like an Atm
...|below]]. Usage information is in [[#Usage|the next section]]. The rest of this page describes the 8Mhz version. The 9.6Mhz code was added later, but is cr
16 KB (2,772 words) - 01:01, 14 November 2020
...hen talking about 9.6 Mhz AVRs, we're actually talking about the ATtiny13. This MCU is fast, small and dirt-cheap, but is also limited in its resources: 64
...his means there is a theoretical limit of 21 LEDs in a string. In practice this is even less, because a typical program will use some stack space. I found
9 KB (1,444 words) - 01:54, 30 November 2020