;=======================================================================
;TITLE: stepper.src
;
;PURPOSE: control up to 3 stepper motors to move in straight lines
; in space. Take commands from a serial port.
;
;AUTHOR: Danny Havenith
; Copyright (c) 2006 Danny Havenith
; Use, modification and distribution is subject to the Boost Software
; License, Version 1.0. (See copy at
; http://www.boost.org/LICENSE_1_0.txt)
;
; UART VP and associated subroutines:
; Copyright © [01/26/1999] Scenix Semiconductor, Inc. All rights reserved.
;
;REVISIONS:
;
;CONNECTIONS:
; ra.0-2 3 keyboard row outputs
; rb.1-3 3 keyboard column inputs for keyboard matrix
; ra.0 is the row output for the 'emergency keys'
; (min, max, emergency stop) and is always enabled (low-active) when motors move
; This pin is also connected to a 'busy'-led.
; ra.3 serial out
; rb.0 serial in
; rb.4-7 Z-axis stepper motor output
; rc.0-3 X-axis stepper motor output
; rc.4-7 Y-axis stepper motor output
;
;
;DETAILS:
; Contains 2 VPs: 1) stepper motor controller 2) serial in/out
;=======================================================================
;-------------------------- DEVICE DIRECTIVES --------------------------
DEVICE SX28,OSCHS1,TURBO
DEVICE STACKX, OPTIONX
IRC_CAL IRC_SLOW
RESET Initialize
;------------------------------ CONSTANTS ------------------------------
;------------------------------ --------- ------------------------------
; The following constants are meant to be changed to configure for
; diverse hardware.
Frequency EQU 4_000_000 ; clock frequency
BaudRate EQU 9600 ; serial port baudrate
InterruptsPerBit EQU 3 ; samples per serial bit
HalfStepsPerSecond EQU 350 ; stepper motor half steps/sec
; uncomment the following EQU if using a MAX232, since we need to
; reverse the rs-232 signals while not using a MAX232
UsingMAX232 EQU 1 ; we're using a max232
;------------------------------ --------- ------------------------------
; some derived constants (derived from the ones above)
; These are not meant to be changed manually.
;
; clock ticks per interrupt
InterruptPeriod EQU Frequency/(InterruptsPerBit * BaudRate) + 1
; value to put in W to obtain the clock ticks per interrupt
; formulated in this particular way to get rid of 'Literal
; truncated to 8 bits' warning
RetiwValue EQU 256-InterruptPeriod
; Interrupts per stepper motor step
StepperDelay EQU Frequency/(HalfStepsPerSecond*InterruptPeriod)
; number of interrupts to pass between detection of the start bit ("flank") and
; the middle of the first bit, plus one (see code for that 'plus one').
StartDelay EQU InterruptsPerBit/2 + InterruptsPerBit + 1
; port definitions
OutputXY EQU rc ; port C outputs the signals for X(0-3) and Y(4-7)
OutputZ EQU rb ; port B outputs the signals for Z on bits(0-3)
KeyboardColumns EQU ra ; port A serves keyboard columns (in a.0-a.2)
KeyboardRows EQU rb ; port B serves keyboard rows (in b.1-b.3)
SerialOut EQU ra.3 ; pins ra.3 and rb.0 are serial output and
SerialIn EQU rb.0 ; input respectively.
;------------------------------ VARIABLES ------------------------------
ORG $08
; 'global' bank, registers that can be accessed regardles of the current
; bank.
ErrorTreshold DS 2 ; Error treshold (for Bresenhams)
Step1 DS 2 ; Step size in the second dimension
Step2 DS 2 ; Step size in the third dimension
; temporary register for interrupt routines
InterruptScratch DS 1
; this byte contains the sign bits for x (.0),y (.1) and z (.2)
Signs DS 1
ORG $10
; bank with registers for the line drawing algorithm
LineDrawingBank EQU $
StepsToGo DS 2 ; steps left on current line
Error2 DS 2 ; cumulative errr in the first dimension
Error1 DS 2 ; cumulative error in the second dimension
StepperDelayCount DS 2 ; timeout between steps
PosX DS 1 ; X, Y and Z pos. 8 bits precision is more
PosY DS 1 ; than enough.
PosZ DS 1
Direction0 DS 1 ; mapping of dimensions (0, 1, 2) to
Direction1 DS 1 ; axes (x, y, z) and direction (up or down).
Direction2 DS 1
StepperState DS 1 ; current stepper state. see below.
; interruptable states, these are pre-empted by a move command
StepperIdle EQU 0 ; Do Nothing
StepperIdleKeys EQU 1 ; Handle keyboard
StepperCountKeys EQU 2 ; Timeout and handle keys
; non-interruptable states. No new vector can be programmed
; while the driver is in one of these states
StepperUpdatePos1 EQU 4 ; Update position 1
StepperUpdatePos2 EQU 5; Update position 2
StepperOutputPos EQU 6 ; latch x,y,z position to outputs
StepperCounting EQU 7 ; wait a while before moving to next position
; update position 0 if wait ends
ORG $30
; this bank contains the results of the commands
; more specifically, the x,y and z vector values
; are kept here...
CommandBank EQU $
Coordinates EQU $
;coordinates must start at an even address, see the parse function
GoX DS 2
GoY DS 2
GoZ DS 2
; command parser variables
CurrentNumber DS 2 ; accumulator for the number we're currently parsing
ParserState DS 1 ; current state
NextChar DS 1 ; next character to parse
CurrentCoordinate DS 1; which coordinate we're parsing.
CurrentCommand DS 1;
CommandFlags DS 1;
; parser states
ParserExpectCommand EQU 0
ParserExpectNumber EQU 1
ParserInHexNumber EQU 2
ParserExpectReturn EQU 3
ORG $50
SERIAL = $ ;UART bank
tx_high ds 1 ;hi byte to transmit
tx_low ds 1 ;low byte to transmit
tx_count ds 1 ;number of bits sent
tx_divide ds 1 ;xmit timing (/16) counter
rx_count ds 1 ;number of bits received
rx_divide ds 1 ;receive timing counter
rx_byte ds 1 ;buffer for incoming byte
flags ds 1 ;only contains the rx_flag
rx_flag EQU flags.0
string ds 1 ;used by send_string to store the address in memory
byte ds 1 ;used by serial routines
;---------------------------- SETTINGS ---------------------------
FREQ Frequency
WKED_W equ $0A ;Write MIWU/RB Interrupt edge setup, 0 = falling, 1 = rising
WKEN_W equ $0B ;Write MIWU/RB Interrupt edge setup, 0 = enabled, 1 = disabled
ST_W equ $0C ;Write Port Schmitt Trigger setup, 0 = enabled, 1 = disabled
LVL_W equ $0D ;Write Port Schmitt Trigger setup, 0 = enabled, 1 = disabled
PLP_W equ $0E ;Write Port Schmitt Trigger setup, 0 = enabled, 1 = disabled
DDIR_W equ $0F ;Write Port Direction
IFDEF UsingMAX232
RA_latch equ %00001111 ;SX18/20/28/48/52 port A latch init
ELSE
RA_latch equ %00000111 ;SX18/20/28/48/52 port A latch init
ENDIF
RA_DDIR equ %11110000 ;see under pin definitions for port A DDIR value
RA_LVL equ %00000000 ;SX18/20/28/48/52 port A LVL value
RA_PLP equ %11111111 ;SX18/20/28/48/52 port A PLP value
RB_latch equ %00000000 ;SX18/20/28/48/52 port B latch init
RB_DDIR equ %00001111 ;SX18/20/28/48/52 port B DDIR value
RB_ST equ %11111111 ;SX18/20/28/48/52 port B ST value
RB_LVL equ %00000000 ;SX18/20/28/48/52 port B LVL value
RB_PLP equ %11111111 ;SX18/20/28/48/52 port B PLP value
RC_latch equ %00000000 ;SX18/20/28/48/52 port C latch init
RC_DDIR equ %00000000 ;SX18/20/28/48/52 port C DDIR value
RC_ST equ %11111111 ;SX18/20/28/48/52 port C ST value
RC_LVL equ %00000000 ;SX18/20/28/48/52 port C LVL value
RC_PLP equ %11111111 ;SX18/20/28/48/52 port C PLP value
;-------------------------- MACRO DEFINITIONS --------------------------
; The following are mainly some macros that define 16 bit, little endian
; versions of the 8-bit instruction set that we all know and have grown to
; love.
; 16-bit little endian decrement
Dec16 MACRO address
sub address, #1 ; remember dec doesn't change C flag
sc
dec address + 1
ENDM
; 16-bit little endian addition
; This addition sets carry flag accordingly (but not the zero flag)
Add16 MACRO dest, src ; little endian 16 bit addition
mov W, src
add dest, W
mov W, src + 1
snb C
movsz W, ++src + 1
add dest + 1, W
ENDM
; 16-bit little endian subtraction
Sub16 MACRO dest,src
sub dest, src ; sub lsb
subb dest + 1, /c ; sub one extra if carry not set (= borrow)
sub dest + 1, src + 1; subtract w from msb
ENDM
; 16-bit, little endian compare, sets zero and carry flag
Cmp16 MACRO dest, src
LOCAL End
mov w, src + 1
mov w, dest + 1 - w
jnz End ; if msb equal...
mov w, src ;...compare lsb
mov w, dest - w ;
End
ENDM
; It's 16 bit
; It's Little endian (or it doesn't matter)
; And, it copies.
Copy16 MACRO dest, src
mov dest, src
mov dest + 1, src + 1
ENDM
; test a 16 bit value for zero, start with the msb, to safely test
; when another 'thread' (interrupt) is decreasing the value.
Test16 MACRO dest
test dest + 1
snz
test dest
ENDM
Clr16 MACRO dest
clr dest
clr dest + 1
ENDM
; move a 16 bit literal into RAM
MovLit16 MACRO dest, literal16
mov dest, #(literal16 // 256)
mov dest + 1, #(literal16 / 256)
ENDM
; These macros control whether our serial line is high-active
; or low-active.
Rs232Up MACRO pin
IFDEF UsingMAX232 THEN
setb pin
ELSE
clrb pin
ENDIF
ENDM
Rs232Down MACRO pin
IFDEF UsingMAX232 THEN
clrb pin
ELSE
setb pin
ENDIF
ENDM
; transfer the state of the rs232 input pin to the carry flag
Rs232PinToCarry MACRO pin
sb pin ;get current rx bit
IFDEF UsingMAX232 THEN
clc
ELSE
stc
ENDIF
snb pin ;
IFDEF UsingMAX232 THEN
stc
ELSE
clc
ENDIF
ENDM
; rather complex macro to generate code that
; produces a line. It puts the absolute components
; in the GoX, GoY and GoZ registers and then composes
; the last three bits of the 'signs' register.
; the expression '||x' takes the absolute value of x.
DoLine MACRO x,y,z
bank CommandBank
MovLit16 GoX, ||x
MovLit16 GoY, ||y
MovLit16 GoZ, ||z
; the following uses the fact that the expression:
; ||(a+1) - ||a + 1
; is zero for a < 0
; is two otherwise. (for integer a)
mov signs, # ( (||(x+1) - ||x + 1) / 2 + (||(y+1) - ||y + 1) + (||(z+1) - ||z + 1) * 2)
call @Move
ENDM
; convert from ascii-coded hex digit to value
; jump if not a true hex digit
; note: this code changes the contents of the fr register
; note: this could probably be optimized
ConvertHexOrJump MACRO fr,address
LOCAL is_digit
cjb fr, #'0', address
cja fr, #'z', address
cjbe fr, #'9', is_digit
or fr, #$20
cjb fr, #'a', address
cja fr, #'f', address
sub fr, #('a' - 10 - '0')
is_digit sub fr, #'0'
ENDM
;-------------------------- INTERRUPT ROUTINE --------------------------
ORG 0
Interrupt
;*********************************************************************************
; Virtual Peripheral: Universal Asynchronous Receiver Transmitter (UART)
; These routines send and receive RS232 serial data, and are currently
; configured (though modifications can be made) for the popular
; "No parity-checking, 8 data bit, 1 stop bit" (N,8,1) data format.
; RECEIVING: The rx_flag is set high whenever a valid byte of data has been
; received and it is the calling routine's responsibility to reset this flag
; once the incoming data has been collected.
; TRANSMITTING: The transmit routine requires the data to be inverted
; and loaded (tx_high+tx_low) register pair (with the inverted 8 data bits
; stored in tx_high and tx_low bit 7 set high to act as a start bit). Then
; the number of bits ready for transmission (10=1 start + 8 data + 1 stop)
; must be loaded into the tx_count register. As soon as this latter is done,
; the transmit routine immediately begins sending the data.
; This routine has a varying execution rate and therefore should always be
; placed after any timing-critical virtual peripherals such as timers,
; adcs, pwms, etc.
; Note: The transmit and receive routines are independent and either may be
; removed, if not needed, to reduce execution time and memory usage,
; as long as the initial "BANK serial" (common) instruction is kept.
;
; Input variable(s) : tx_low (only high bit used), tx_high, tx_count
; Output variable(s) : rx_flag, rx_byte
; Variable(s) affected : tx_divide, rx_divide, rx_count
; Flag(s) affected : rx_flag
;
;*********************************************************************************
SerialVP
bank SERIAL ;switch to serial register bank
:transmit decsz tx_divide ;only execute the transmit routine
jmp :receive ;
mov w,#InterruptsPerBit ;
mov tx_divide,w ;
test tx_count ;are we sending?
snz ;
jmp :receive ;
stc ;yes, ready stop bit
rr tx_high ; and shift to next bit
rr tx_low ;
dec tx_count ;decrement bit counter
snb tx_low.6 ;output next bit
Rs232Up SerialOut ;
sb tx_low.6 ;
Rs232Down SerialOut ;
; transfer input to carry flag.
:receive Rs232PinToCarry SerialIn
test rx_count ;currently receiving byte?
sz ;
jmp :rxbit ;if so, jump ahead
mov w,#9 ;in case start, ready 9 bits
sc ;skip ahead if not start bit
mov rx_count,w ;it is, so renew bit count
mov w,#StartDelay ;ready 1.5 bit periods plus one
mov rx_divide,w ;
:rxbit decsz rx_divide ;middle of next bit?
jmp :rxdone ;
mov w,#InterruptsPerBit ;yes, ready 1 bit period
mov rx_divide,w ;
dec rx_count ;last bit?
sz ;if not
rr rx_byte ; then save bit
snz ;if so,
setb rx_flag ; then set flag
:rxdone ; else, exit
; Stepper motor controller.
; This VP controls up to 3 stepper motors. It implements Bresenhams algorithm
; to move in a straight line in 3D coordinate space.
Stepper
bank LineDrawingBank
mov w, StepperState
jmp pc + w
jmp :ZeroStepperOutputs ; idle, do noting
jmp :EndStepper ; idle, handle keyboard
jmp :EndStepper ; timeout while handling keyboard
jmp :EndStepper ; state 3 not used
; non-interruptable states
jmp :DoUpdatePos1 ; update pos1
jmp :DoUpdatePos2 ; update pos2
jmp :OutputStepper; latch x,y,z-positions to outputs
; state #7 no jump, just sstart executing here
; wait a while before moving to next position
Dec16 StepperDelayCount
Test16 StepperDelayCount
jnz :EndStepper
; transition to update position state
mov StepperState, #StepperUpdatePos1
MovLit16 StepperDelayCount, StepperDelay
; make a step in the first direction
Dec16 StepsToGo
mov w, Direction0
call MakeStep
jmp :EndStepper
; set all stepper outputs to zero
; this should decrease current when steppers are
; idle.
:ZeroStepperOutputs
clr OutputXY
mov w, OutputZ
and w, #%00001111
mov OutputZ, w
jmp :EndStepper
; update position 1 state
:DoUpdatePos1
Add16 Error1, Step1
jc :Change1
Cmp16 Error1, ErrorTreshold
jnc :EndUpdatePos1
:Change1
Sub16 Error1, ErrorTreshold
mov w, Direction1
call MakeStep
:EndUpdatePos1
mov StepperState, #StepperUpdatePos2
jmp :EndStepper
; update position 2 state
:DoUpdatePos2
Add16 Error2, Step2
jc :Change2
Cmp16 Error2, ErrorTreshold
jnc :TransitionToOutputPos
:Change2
Sub16 Error2, ErrorTreshold
mov w, Direction2
call MakeStep
:TransitionToOutputPos
; transition to outputpos state
mov StepperState, #StepperOutputPos
jmp :EndStepper
; output positions state
:OutputStepper ; now translate x,y and z to stepper
; line outputs
; first move x and y to combined
; XY output (4 bits each)
mov w, PosX
call ExpandPos
mov InterruptScratch, w
mov w, PosY
call ExpandPos2
or w, InterruptScratch
mov OutputXY, w
mov w, PosZ
call ExpandPos2 ; translate z pos to high bits
mov InterruptScratch, w
mov w, OutputZ
and w, #%00001111
or w, InterruptScratch
mov OutputZ, w
mov StepperState, #StepperCounting
Test16 StepsToGo
jnz :EndStepper ; if steps to go is zero, transition to idle
mov StepperState, #StepperIdle
:EndStepper
EndInterrupt mov w, #RetiwValue
retiw
MakeStep ; increase or decrease an axis dimension, depending on the value of w
; w.7 determines whether we increase or decrease (1 = increase)
; w.1 and w.0 determine which axis (0 = x, 1 = y, 2 = z, 3 = crash horibly)
mov InterruptScratch, w
jb InterruptScratch.7, :Increase
and w, #3
jmp PC + w
jmp :DecreaseX
jmp :DecreaseY
jmp :DecreaseZ
:Increase and w, #3
jmp PC + w
jmp :IncreaseX
jmp :IncreaseY
jmp :IncreaseZ
:IncreaseZ inc PosZ
retp
:IncreaseY inc PosY
retp
:IncreaseX inc PosX
retp
:DecreaseZ dec PosZ
retp
:DecreaseY dec PosY
retp
:DecreaseX dec PosX
retp
ExpandPos ; convert from number (0-3) to
; bit pattern (0001, 0010, 0100, 1000)
and w, #7
jmp PC+w
; retw %0001, %0100, %0010, %1000, %0001, %0100, %0010, %1000
retw %0001, %0011, %0010, %0110, %0100, %1100, %1000, %1001
; retw %0001, %0101, %0100, %0110, %0010, %1010, %1000, %1001
ExpandPos2 ; easiest way to create a bit pattern in upper
; bits is to have another version of Expand
; instead of swapping
and w, #7
jmp PC+w
; retw %00010000, %00100000, %01000000, %10000000
retw %00010000, %00110000, %00100000, %01100000, %01000000, %11000000, %10000000, %10010000
;------------------------ INITIALIZATION ROUTINE -----------------------
Initialize
;<group comment>
mov m, #ST_W ;point MODE to write ST register
mov w,#RB_ST ;Setup RB Schmitt Trigger, 0 = enabled, 1 = disabled
mov !rb,w
mov w,#RC_ST ;Setup RC Schmitt Trigger, 0 = enabled, 1 = disabled
mov !rc,w
mov m, #LVL_W ;point MODE to write LVL register
mov w,#RA_LVL ;Setup RA CMOS or TTL levels, 0 = TTL, 1 = CMOS
mov !ra,w
mov w,#RB_LVL ;Setup RB CMOS or TTL levels, 0 = TTL, 1 = CMOS
mov !rb,w
mov w,#RC_LVL ;Setup RC CMOS or TTL levels, 0 = TTL, 1 = CMOS
mov !rc,w
mov w,#RA_PLP ;Setup RA Weak Pull-up, 0 = enabled, 1 = disabled
mov !ra,w
mov w,#RB_PLP ;Setup RB Weak Pull-up, 0 = enabled, 1 = disabled
mov !rb,w
mov w,#RC_PLP ;Setup RC Weak Pull-up, 0 = enabled, 1 = disabled
mov !rc,w
mov m, #DDIR_W ;point MODE to write DDIR register
mov w,#RA_DDIR ;Setup RA Direction register, 0 = output, 1 = input
mov !ra,w
mov w,#RB_DDIR ;Setup RB Direction register, 0 = output, 1 = input
mov !rb,w
mov w,#RC_DDIR ;Setup RC Direction register, 0 = output, 1 = input
mov !rc,w
mov w,#RA_latch ;Initialize RA data latch
mov ra,w
mov w,#RB_latch ;Initialize RB data latch
mov rb,w
mov w,#RC_latch ;Initialize RC data latch
mov rc,w
; zero all ram (SX28)
clr fsr ;reset all ram banks
:zero_ram sb fsr.4 ;are we on low half of bank?
setb fsr.3 ;If so, don't touch regs 0-7
clr ind ;clear using indirect addressing
incsz fsr ;repeat until done
jmp :zero_ram
mov !option,#%10011111 ;enable rtcc interrupt
;---------------------------- MAIN PROGRAM -----------------------------
Main
bank SERIAL
mov w, #OpeningMessage // 256; modulo to prevent warning
call @send_string
MainLoop
bank SERIAL
call @get_byte ; read a byte from serial port
call @send_byte ; echo that same byte
mov w, byte ; re-retreive the received byte
bank CommandBank
mov NextChar, w
call @ParseCharacter ; parse the byte and act
test CommandFlags
snz
jmp MainLoop
clr CommandFlags
; for now, we only have 1 command, so assume
; 'M' was issued.
call @Move
mov w, #Prompt // 256
call @send_string
jmp MainLoop
ORG $200
SendPrompt bank SERIAL
mov w, #'>'
call @send_byte
mov w, #13
call @send_byte
mov w, #10
call @send_byte
retp
Move ; program the vector in GoX, GoY and GoZ
; into the Bresenham registers and start the
; algorithm.
; If the Bresenham routine is busy, wait until it's
; finished
bank LineDrawingBank
; wait until the stepper is interruptible
:Wait jb StepperState.2, :Wait
; now start to determine which value is the largest
; Bresenhams algoritm is driven by the largest component
; on every 'tick' a step is made in that direction and other
; directions may or may not make a step in that same tick.
bank CommandBank
Cmp16 GoX, GoY
jnc :YOrZIsLargest ; jump if (Y > X)
:XOrZIsLargest
Cmp16 GoX, GoZ
jnc :ZIsLargest ; jump if (Z > X)
:XIsLargest ; x is largest, order becomes x, y, z
Copy16 ErrorTreshold, GoX
Copy16 Step1, GoY
Copy16 Step2, GoZ
bank LineDrawingBank
; first set the direction registers
; the direction registers map Bresenhams registers
; (0, 1, and 2) to the three axis (x, y and z)
;
; these are coded 0 for x, 1 for y and 2 for z
; we set them to a value 'shifted left' (times 2)
; because we're going to shift them to the right
; lateron to add the direction bits.
mov Direction0, #0 ; 2 times 0, for x
mov Direction1, #2 ; 2 times 1, for y
mov Direction2, #4 ; 2 times 2, for z
; now distribute the direction (up or down) bits
rr Signs
rr Direction0 ; x to Direction0
rr Signs
rr Direction1 ; y to Direction1
rr Signs
rr direction2 ; z to Direction2
jmp :Finalize
:YOrZIsLargest
Cmp16 GoY, GoZ
jnc :ZIsLargest
:YIsLargest ; y is largest, order becomes y, x, z
Copy16 ErrorTreshold, GoY
Copy16 Step1, GoX
Copy16 Step2, GoZ
bank LineDrawingBank
; first set the direction registers
; the direction registers map Bresenhams registers
; (0, 1, and 2) to the three axis (x, y and z)
;
; these are coded 0 for x, 1 for y and 2 for z
; we set them to a value 'shifted left' (times 2)
; because we're going to shift them to the right
; lateron to add the direction bits.
mov Direction0, #2 ; 2 times 1, for y
mov Direction1, #0 ; 2 times 0, for x
mov Direction2, #4 ; 2 times 2, for z
; now distribute the direction (up or down) bits
rr Signs
rr Direction1 ; x to Direction1
rr Signs
rr Direction0 ; y to Direction0
rr Signs
rr direction2 ; z to Direction2
jmp :Finalize
:ZIsLargest ; z is largest, order becomes z, x, y
Copy16 ErrorTreshold, GoZ
Copy16 Step1, GoX
Copy16 Step2, GoY
bank LineDrawingBank
; first set the direction registers
; the direction registers map Bresenhams registers
; (0, 1, and 2) to the three axis (x, y and z)
;
; these are coded 0 for x, 1 for y and 2 for z
; we set them to a value 'shifted left' (times 2)
; because we're going to shift them to the right
; lateron to add the direction bits.
mov Direction0, #4 ; 2 times 2, for z
mov Direction1, #0 ; 2 times 0, for x
mov Direction2, #2 ; 2 times 1, for y
; now distribute the direction (up or down) bits
rr Signs
rr Direction1 ; x to Direction1
rr Signs
rr Direction2 ; y to Direction2
rr Signs
rr direction0 ; z to Direction0
BREAK :Finalize
:Finalize
; Error1 = ErrorTreshold/2
Copy16 Error1, ErrorTreshold
rr Error1 + 1
rr Error1
; Error2 = Error1
Copy16 Error2, Error1
; Set StepsToGo
Copy16 StepsToGo, ErrorTreshold
MovLit16 StepperDelayCount, StepperDelay
; now set the state to 'output position'
; this will activate the stepper.
mov StepperState, #StepperOutputPos
retp
; parse an input character
; This routine is used to parse input command strings
; an example input string would be
; 'm 1ff, 0, FFFF'
; which stands for 'Move 511, 0, 65535'
ParseCharacter
bank CommandBank
mov w, ParserState
jmp PC + w
jmp :DoExpectCommand
jmp :DoExpectNumber
jmp :DoInNumber
:DoExpectReturn
mov w, #13 ; carriage return
mov w, NextChar - w
sz ; do nothing unless we have a cr
retp
mov ParserState, #ParserExpectCommand
or CommandFlags, #$01
retp ; call the 'move' routine and return
:DoExpectCommand
mov w, #'M'
mov w, NextChar - w
and w, #~$20 ; tolower
sz ; return if it is not 'm' (the only command we support so far
retp
mov CurrentCommand, #'M'
Clr16 GoX
Clr16 GoY
Clr16 GoZ
mov Signs, #$07; all positive
mov CurrentCoordinate, #1 ; start parsing x
mov ParserState, #ParserExpectNumber
retp
:DoExpectNumber
ConvertHexOrJump NextChar, :EndExpectNumber
mov ParserState, #ParserInHexNumber
mov CurrentNumber, NextChar
clr CurrentNumber + 1
:EndExpectNumber
cse NextChar, #'-' ; return if not '-'...
retp
mov w, /CurrentCoordinate
and Signs, w ; reset the corresponding sign bit
retp
:DoInNumber ConvertHexOrJump NextChar, :EndInNumber
; now CurrentCoordinate = CurrentCoordinate * 16 + nextdigit
; todo: optimize
clc
rl CurrentNumber
rl CurrentNumber + 1
rl CurrentNumber
rl CurrentNumber + 1
rl CurrentNumber
rl CurrentNumber + 1
rl CurrentNumber
rl CurrentNumber + 1
mov w, NextChar
and w, #$0f
or CurrentNumber, w
retp
:EndInNumber
; calculate the destination address
mov w, #Coordinates
add w, CurrentCoordinate
and w, #$fe
; copy the parsed number to the address
mov FSR, w
mov IND, CurrentNumber
inc FSR
mov IND, CurrentNumber + 1
; if this was not the last coordinate,
; goto ExpectNumber state
; else goto ExpectReturn state
mov w, #ParserExpectNumber
snb CurrentCoordinate.2
mov w, #ParserExpectReturn
mov ParserState, w
clc
rl CurrentCoordinate
; immediately reparse this character
jmp ParseCharacter
ORG $400
;*****************************************************************************************
; UART Subroutines
;*****************************************************************************************
;*********************************************************************************
; Function: get_byte
; Get byte via serial port and echo it back to the serial port
; INPUTS:
; -NONE
; OUTPUTS:
; -received byte in rx_byte
;*********************************************************************************
get_byte bank SERIAL
sb rx_flag ;wait till byte is received
jmp get_byte
clrb rx_flag ;reset the receive flag
mov w,rx_byte ;store byte (copy using W)
mov byte,w ; & fall through to echo char back
retp
;*********************************************************************************
; Function: send_byte
; Send byte via serial port
; INPUTS:
; w - The byte to be sent via RS-232
; OUTPUTS:
; outputs the byte via RS-232
;*********************************************************************************
send_byte bank SERIAL
:wait test tx_count ;wait for not busy
sz
jmp :wait ;
;not w ;ready bits (inverse logic)
mov tx_high,w ; store data byte
clrb tx_low.7 ; set up start bit
mov w,#10 ;1 start + 8 data + 1 stop bit
mov tx_count,w
retp ;leave and fix page bits
;*********************************************************************************
; Function: send_string
; Send string pointed to by address in W register
; INPUTS:
; w - The address of a null-terminated string in program
; memory
; OUTPUTS:
; outputs the string via RS-232
;*********************************************************************************
send_string bank SERIAL
mov string,w ;store string address
:loop mov w,string ;read next string character
mov m,#(StringPage>>8) ;with indirect addressing
iread ;using the mode register
test w ;are we at the last char?
snz ;if not=0, skip ahead
jmp :exit ;yes, leave & fix page bits
call send_byte ;not 0, so send character
inc string ;point to next character
jmp :loop ;loop until done
:exit mov m,#$0f ;reset the mode register
retp
;*****************************************************************************************
; String constants
;*****************************************************************************************
org $500
StringPage EQU $
OpeningMessage DW '3D Stepper Control v1.0', 13
DW 'J&J Productions 2006', 13
; notice the missing zero at the above line.
Prompt DW '>', 0