Actions

Difference between revisions of "Bluetooth serial modules"

From Just in Time

(Created page with "The bluetooth modules that are offered on ebay all seem to have the same hardware, but have different firmware. This page has some notes on the ones that we have. ==Bolutek==...")
 
m
Line 5: Line 5:
 
''+BOLUTEK Firmware V2.43, Bluetooth V2.0, HCI V2.1, HCI Rev37, LMP V4, LMP SubV37''
 
''+BOLUTEK Firmware V2.43, Bluetooth V2.0, HCI V2.1, HCI Rev37, LMP V4, LMP SubV37''
  
−
'''AT+HELP''' Gives a list of commands:
 
−
<pre>
 
−
Command              Description
 
−
-----------------------------------------------------------------
 
−
AT                  Check if the command terminal work normally
 
−
AT+RESET            Software reboot
 
−
AT+VERSION          Get firmware, bluetooth, HCI and LMP version
 
−
AT+HELP              List all the commands
 
−
AT+NAME              Get/Set local device name
 
−
AT+PIN              Get/Set pin code for pairing
 
−
AT+BAUD              Get/Set baud rate
 
−
AT+CLEAR            Remove the remembered remote address
 
−
AT+LADDR            Get local bluetooth address
 
−
AT+RNAME            Get remote device name
 
−
AT+DEFAULT          Restore factory default
 
−
AT+CMODE            Get/Set connection mode
 
−
AT+BIND              Get/Set bind bluetooth address
 
−
AT+COD              Get/Set local class of device
 
−
AT+IAC              Get/Set inquiry access code
 
−
AT+ROLE              Get/Set master or slave mode
 
−
AT+STATE            Get current state
 
−
AT+SENM              Get/Set security and encryption mode
 
−
AT+IPSCAN            Get/Set page and inquiry scan parameters
 
−
AT+SNIFF            Get/Set sniff power table parameters
 
−
AT+LOWPOWER          Start/Stop low power mode
 
−
AT+UARTMODE          Get/Set uart stop bits and parity
 
−
AT+ENABLEIND        Enable/Disable Indication print
 
−
AT+LSP              List Paired Device List
 
−
AT+RESETPDL          Reset Paired Device List
 
−
AT+REMOVEPDL        Remove one entry from Paired Device List
 
−
AT+SUPERVISION      Get/Set supervision timeout
 
−
AT+AUTOINQ          Start/Stop auto inquiry
 
−
AT+INQ              Start inquiry
 
−
AT+INQC              Cancel ongoing inquiry
 
−
(M)AT+AUTOCONN      Start/Stop auto connection
 
−
(M)AT+INQM          Get/Set inquiry parameters
 
−
(M)AT+CONNECT        Connect to a remote device by BD address
 
−
-----------------------------------------------------------------
 
−
Note: (M) = The command support master mode only, other commands
 
−
support both master and slave mode.
 
−
For more information, please visit http://www.bolutek.cn
 
−
Copyright@2012 www.bolutek.cn. All rights reserved.
 
−
</pre>
 
  
 
Default name is ''Bolutek'' and default PIN is ''1234''.
 
Default name is ''Bolutek'' and default PIN is ''1234''.
 +
 +
===AT commands===
 +
The following tables are from [http://www.electrodragon.com/w/index.php?title=BC04 electrodragon.com] and have been copied here for reference.
 +
 +
==== Downlink Command ====
 +
{| class="wikitable"
 +
|-
 +
! Command Name !! Command !! Response !! Parameter
 +
|-
 +
| testing connection || AT || OK || Null
 +
|-
 +
| Check version || AT+VERSION || +VERSION=<Para1> || <Para1>: Firmware version number, the Bluetooth version number, <br /> the local HCI version, HCI amendments, <br /> LMP version number, LMP sub-version number
 +
|-
 +
| check help || AT+HELP || ...||
 +
|-
 +
| check/set name || AT+NAME <br />AT+NAME< Para1> || OK or error || <Para1>：device name
 +
|-
 +
| Reset to default || AT+DEFAULT || OK || null
 +
|-
 +
| reset || AT+ RESET ||  OK || null
 +
|-
 +
| check/set pins || AT+PIN <br />AT+PIN< Para1> || OK or error || <Para1>: pins
 +
|-
 +
| check/set baud rate || AT+BAUD <br /> AT+BAUD< Para1> || OK or error || 1---1200 <br /> 2---2400 <br />3---4800 <br />4---9600 <br />5---19200 <br />6---38400 <br />7---57600 <br />8---115200 <br />9---230400 <br />A---460800 <br />B---921600 <br />C---1382400 <br />Default ：4---9600
 +
|-
 +
| check/set device type || AT+COD <br /> AT+COD< Para1>,<Para2> || OK or error  || <Para1>: Local device type (length must be 6 bytes) from the mode is in effect, <br />the end retrieval<br /><Para2>: Filtration equipment type effect in the main mode for filtering <br />search to equipment (if you set 000,000 returns all search equipment) default: 001f00, 000000
 +
|-
 +
| check/set module SPP master/slave mode || AT+ROLE <br /> AT+ROLE< Para1> || OK or error || <Para1>: 0 --- from the device; <br />1 --- master; Default: 0 from equipment
 +
|-
 +
| check/set GIAC || AT+IAC< Para1> || OK or Error || <Para1>: The query access code, default value: 9e8b33 <br />specific settings, see Appendix 2: query access code Description
 +
|-
 +
| check/set remote bluetooth device name || AT+RNAME< Para1> || OK or Error || <Para1>: remote Bluetooth device address
 +
|-
 +
| check/set inquiry mode || AT+INQM<Para1>,<Para2>,<Para3> || OK or Error || <Para1>: Query mode: 0: inquiry_mode_standard,1: inquiry_mode_rssi, <br />2: inquiry_mode_eir, Length: 1 byte, <br /><Para2>: Up Bluetooth Device response, Length: 2 bytes, <br /><Para3>: Query timeout, Timeout range :1-30(Converted into time :1.28-61.44 seconds), Length: 2 bytes, Default: 1,9,30 (16 hex)
 +
|-
 +
| check/set connection mode || AT+CMODE< Para1> || OK or Error || <Para1>:<br />0: specified Bluetooth address connected mode <br />(specified Bluetooth address set by the BIND command)
 +
1: Any Bluetooth address connection mode <br />(not the BIND command set address the constraints), the default value:
 +
|-
 +
| check/set bluetooth address || AT+BIND<Para1> || OK or Error || <Para1>:<br />
 +
Set binding Bluetooth address format: 11,22,33,44,55,66<br />
 +
Reply the Bluetooth address format: 11:22:33:44:55:66<br />
 +
Default: 00:00:00:00:00:00<br />
 +
|-
 +
| clear memory address || AT+CLEAR || OK || Null
 +
|-
 +
| check/set UART MODE || AT+ UARTMODE<Para1>,<Para2> || OK or Error || <Para1>: Stop bit: 0:1 stop bit, 1:2 stop bit<br />
 +
<Para2>: Parity: 0: no parity, 1: Odd, 2: Even parity, default value: 0,0
 +
|-
 +
| check local BT address || AT+LADDR || +LADDR=<Para1> || <Para1>: Local Bluetooth address, <br />for example: 11:22:33:44:55:66
 +
|-
 +
| checkt BT module working status || AT+STATE || +STATE=<Para1> || Example
 +
|-
 +
| check/set Remote Bluetooth device automatically search || AT+ AUTOINQ<Para1> || Ok or Error || 0=no, 1=yes
 +
|-
 +
| check remote bluetooth device || AT+INQ  || Ok || null
 +
|-
 +
| cancel check remote bluetooth device || AT+INQC  || Ok || null
 +
|-
 +
| check/set Whether to automatically connect to a remote Bluetooth device || AT+ AUTOCONN<Para1>  || OK or Error || 0=Not Auto, 1= Auto
 +
|-
 +
| Connect to remote bluetooth device || AT+CONNECT<Para1>  || OK or Error|| <Para1>:
 +
Set the remote bluetooth address format:<br />
 +
11,22,33,44,55,66<br />
 +
Reply Bluetooth address format:<br />
 +
11:22:33:44:55:66<br />
 +
|-
 +
| check/set Page scan and inquiry scan parameters || AT+IPSCAN<Para1>,<Para2>,<Para3>,<Para4> || OK or Error || <Para1>: Query interval<br />
 +
<Para2>: Query duration<br />
 +
<Para3>: Paging time intervals<br />
 +
<Para4>: Paging duration<br />
 +
The above parameters are hexadecimal numbers.<br />
 +
Default: 800,12,800,12<br />
 +
|-
 +
| check/set Encrypt mode || AT+SENM<Para1>,<Para2>  || OK or Error|| <Para1>: Safe mode, the following values ​​(1 byte):<br />
 +
0 - sec_mode0_off<br />
 +
1 - sec_mode1_non_secure<br />
 +
2 - sec_mode2_service<br />
 +
3 - sec_mode3_link<br />
 +
4 - sec_mode4_ssp<br />
 +
<Para2>: Encryption mode, the following values ​​(1 byte):<br />
 +
0 - hci_enc_mode_off<br />
 +
1 - hci_enc_mode_pt_to_pt<br />
 +
2 - hci_enc_mode_pt_to_pt_and_bcast<br />
 +
Default: 0,0<br />
 +
|-
 +
| Check/set low power Mode || AT+ LOWPOWER<Para1>  ||ok or error || 0=not support, 1=support, default =1
 +
|-
 +
| check/set sniff energy save mode || AT+SNIFF<Para1>,<Para2>,<Para3>,<Para4> || ok or error || <Para1> - max time, <Para2> - min time, <Para3> - trial time, <Para4> - timeout time
 +
|-
 +
| check/set indication upward command || AT+ENABLEIND<Para1> || ok or error || 0= close, 1= open, default 1
 +
|-
 +
| check Bluetooth pairing list || AT+LSP || LSP=<Para1>,<Para2>,<Para3> <br />……<br />LSP=E <br /> || <Para1>：number（0-7）<br /><Para2>：bluetooth address code <br /> <Para3>：name<br /> default feedback：LSP=E <br />
 +
|-
 +
| Clear all bluetooth pairing list || AT+RESETPDL || Ok || -
 +
|-
 +
| clear selected bluetooth pairing record || AT+REMOVEPDL<Para1> || OK || <Para1>：number（0-7）
 +
|-
 +
| check/set linkloss checking time || AT+SUPERVISION<Para1> || Ok or error || <Para1> response time, unit in second (Hex), default 5
 +
|}
 +
==== Uplink Command list ====
 +
{| class="wikitable"
 +
|-
 +
! Command Name !! Command !! Response !! Parameter
 +
|-
 +
| ready || +READY || - || -
 +
|-
 +
| inquiry status || +INQUIRING || - || -
 +
|-
 +
| inquiry pairing status || +PAIRABLE ||-||-
 +
|-
 +
| connecting || +CONNECTING<Para1> || - ||-
 +
|-
 +
| connected || +CONNECTED || - ||-
 +
|-
 +
| connection fail || +CONNECTION FAILED || - ||-
 +
|-
 +
| report remote bluettoth device name || +RNAME=<Para1> || <Para1>： report remote bluetooth name
 +
|-
 +
| report inquiry result || +INQS start inquiry<br />
 +
+INQ=<Para1>,<Para2>,<Para3> <br />
 +
……      device information <br />
 +
+INQE inquiry completed <br />
 +
||
 +
<Para1>：bluetooth address<br />
 +
format：11:22:33:44:55:66 <br />
 +
<Para2>：device type<br />
 +
<Para3>：RSSI signal strength (normal is decimal) signal strengthness (default in decimal return 7fff when is not available) <br />

Revision as of 00:12, 28 February 2013

The bluetooth modules that are offered on ebay all seem to have the same hardware, but have different firmware. This page has some notes on the ones that we have.

Bolutek

Initially at 9600bps, commands terminated with crlf and recognized by the following response to AT+VERSION: +BOLUTEK Firmware V2.43, Bluetooth V2.0, HCI V2.1, HCI Rev37, LMP V4, LMP SubV37


Default name is Bolutek and default PIN is 1234.

AT commands

The following tables are from electrodragon.com and have been copied here for reference.

Downlink Command

Command Name Command Response Parameter
testing connection AT OK Null
Check version AT+VERSION +VERSION=<Para1> <Para1>: Firmware version number, the Bluetooth version number,
the local HCI version, HCI amendments,
LMP version number, LMP sub-version number
check help AT+HELP ...
check/set name AT+NAME
AT+NAME< Para1>		 OK or error <Para1>：device name
Reset to default AT+DEFAULT OK null
reset AT+ RESET OK null
check/set pins AT+PIN
AT+PIN< Para1>		 OK or error <Para1>: pins
check/set baud rate AT+BAUD
AT+BAUD< Para1>		 OK or error 1---1200
2---2400
3---4800
4---9600
5---19200
6---38400
7---57600
8---115200
9---230400
A---460800
B---921600
C---1382400
Default ：4---9600
check/set device type AT+COD
AT+COD< Para1>,<Para2>		 OK or error <Para1>: Local device type (length must be 6 bytes) from the mode is in effect,
the end retrieval
<Para2>: Filtration equipment type effect in the main mode for filtering
search to equipment (if you set 000,000 returns all search equipment) default: 001f00, 000000
check/set module SPP master/slave mode AT+ROLE
AT+ROLE< Para1>		 OK or error <Para1>: 0 --- from the device;
1 --- master; Default: 0 from equipment
check/set GIAC AT+IAC< Para1> OK or Error <Para1>: The query access code, default value: 9e8b33
specific settings, see Appendix 2: query access code Description
check/set remote bluetooth device name AT+RNAME< Para1> OK or Error <Para1>: remote Bluetooth device address
check/set inquiry mode AT+INQM<Para1>,<Para2>,<Para3> OK or Error <Para1>: Query mode: 0: inquiry_mode_standard,1: inquiry_mode_rssi,
2: inquiry_mode_eir, Length: 1 byte,
<Para2>: Up Bluetooth Device response, Length: 2 bytes,
<Para3>: Query timeout, Timeout range :1-30(Converted into time :1.28-61.44 seconds), Length: 2 bytes, Default: 1,9,30 (16 hex)
check/set connection mode AT+CMODE< Para1> OK or Error <Para1>:
0: specified Bluetooth address connected mode
(specified Bluetooth address set by the BIND command)

1: Any Bluetooth address connection mode
(not the BIND command set address the constraints), the default value:

check/set bluetooth address AT+BIND<Para1> OK or Error <Para1>:

Set binding Bluetooth address format: 11,22,33,44,55,66
Reply the Bluetooth address format: 11:22:33:44:55:66
Default: 00:00:00:00:00:00

clear memory address AT+CLEAR OK Null
check/set UART MODE AT+ UARTMODE<Para1>,<Para2> OK or Error <Para1>: Stop bit: 0:1 stop bit, 1:2 stop bit

<Para2>: Parity: 0: no parity, 1: Odd, 2: Even parity, default value: 0,0

check local BT address AT+LADDR +LADDR=<Para1> <Para1>: Local Bluetooth address,
for example: 11:22:33:44:55:66
checkt BT module working status AT+STATE +STATE=<Para1> Example
check/set Remote Bluetooth device automatically search AT+ AUTOINQ<Para1> Ok or Error 0=no, 1=yes
check remote bluetooth device AT+INQ Ok null
cancel check remote bluetooth device AT+INQC Ok null
check/set Whether to automatically connect to a remote Bluetooth device AT+ AUTOCONN<Para1> OK or Error 0=Not Auto, 1= Auto
Connect to remote bluetooth device AT+CONNECT<Para1> OK or Error <Para1>:

Set the remote bluetooth address format:
11,22,33,44,55,66
Reply Bluetooth address format:
11:22:33:44:55:66

check/set Page scan and inquiry scan parameters AT+IPSCAN<Para1>,<Para2>,<Para3>,<Para4> OK or Error <Para1>: Query interval

<Para2>: Query duration
<Para3>: Paging time intervals
<Para4>: Paging duration
The above parameters are hexadecimal numbers.
Default: 800,12,800,12

check/set Encrypt mode AT+SENM<Para1>,<Para2> OK or Error <Para1>: Safe mode, the following values ​​(1 byte):

0 - sec_mode0_off
1 - sec_mode1_non_secure
2 - sec_mode2_service
3 - sec_mode3_link
4 - sec_mode4_ssp
<Para2>: Encryption mode, the following values ​​(1 byte):
0 - hci_enc_mode_off
1 - hci_enc_mode_pt_to_pt
2 - hci_enc_mode_pt_to_pt_and_bcast
Default: 0,0

Check/set low power Mode AT+ LOWPOWER<Para1> ok or error 0=not support, 1=support, default =1
check/set sniff energy save mode AT+SNIFF<Para1>,<Para2>,<Para3>,<Para4> ok or error <Para1> - max time, <Para2> - min time, <Para3> - trial time, <Para4> - timeout time
check/set indication upward command AT+ENABLEIND<Para1> ok or error 0= close, 1= open, default 1
check Bluetooth pairing list AT+LSP LSP=<Para1>,<Para2>,<Para3>
……
LSP=E
<Para1>：number（0-7）
<Para2>：bluetooth address code
<Para3>：name
default feedback：LSP=E
Clear all bluetooth pairing list AT+RESETPDL Ok -
clear selected bluetooth pairing record AT+REMOVEPDL<Para1> OK <Para1>：number（0-7）
check/set linkloss checking time AT+SUPERVISION<Para1> Ok or error <Para1> response time, unit in second (Hex), default 5

Uplink Command list

Command Name Command Response Parameter
ready +READY - -
inquiry status +INQUIRING - -
inquiry pairing status +PAIRABLE - -
connecting +CONNECTING<Para1> - -
connected +CONNECTED - -
connection fail +CONNECTION FAILED - -
report remote bluettoth device name +RNAME=<Para1> <Para1>： report remote bluetooth name
report inquiry result +INQS start inquiry

+INQ=<Para1>,<Para2>,<Para3>
…… device information
+INQE inquiry completed

<Para1>：bluetooth address
format：11:22:33:44:55:66
<Para2>：device type
<Para3>：RSSI signal strength (normal is decimal) signal strengthness (default in decimal return 7fff when is not available)

Retrieved from "https://rurandom.org/justintime/index.php?title=Bluetooth_serial_modules&oldid=949"