Difference between revisions of "ATtiny4313 AVRDude configuration"
From Just in Time
m (moved This link to ATtiny4313 AVRDude configuration) |
|||
| Line 1: | Line 1: | ||
| − | The following entry | + | The following entry appears to work for programming the Attiny4313 with Avrdude, though it hasn't been thoroughly tested yet. |
| + | |||
| + | We don't take any responsibility for anyone trying this and frying their Tinies or Programmer !! Be sure you know what you are doing. | ||
<pre> | <pre> | ||
Revision as of 11:43, 30 July 2010
The following entry appears to work for programming the Attiny4313 with Avrdude, though it hasn't been thoroughly tested yet.
We don't take any responsibility for anyone trying this and frying their Tinies or Programmer !! Be sure you know what you are doing.
#------------------------------------------------------------
# ATtiny4313 (Clone off 2313)
#------------------------------------------------------------
part
id = "t4313";
desc = "ATtiny4313";
has_debugwire = yes;
flash_instr = 0xB2, 0x0F, 0x1F;
eeprom_instr = 0xBB, 0xFE, 0xBB, 0xEE, 0xBB, 0xCC, 0xB2, 0x0D,
0xBA, 0x0F, 0xB2, 0x0F, 0xBA, 0x0D, 0xBB, 0xBC,
0x99, 0xE1, 0xBB, 0xAC;
stk500_devcode = 0x23;
## Use the ATtiny26 devcode:
avr910_devcode = 0x5e;
signature = 0x1e 0x92 0x0d;
pagel = 0xD4;
bs2 = 0xD6;
reset = io;
chip_erase_delay = 9000;
pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
"x x x x x x x x x x x x x x x x";
chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
"x x x x x x x x x x x x x x x x";
timeout = 200;
stabdelay = 100;
cmdexedelay = 25;
synchloops = 32;
bytedelay = 0;
pollindex = 3;
pollvalue = 0x53;
predelay = 1;
postdelay = 1;
pollmethod = 1;
pp_controlstack =
0x0E, 0x1E, 0x0E, 0x1E, 0x2E, 0x3E, 0x2E, 0x3E,
0x4E, 0x5E, 0x4E, 0x5E, 0x6E, 0x7E, 0x6E, 0x7E,
0x26, 0x36, 0x66, 0x76, 0x2A, 0x3A, 0x6A, 0x7A,
0x2E, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
hventerstabdelay = 100;
progmodedelay = 0;
latchcycles = 5;
togglevtg = 1;
poweroffdelay = 15;
resetdelayms = 1;
resetdelayus = 0;
hvleavestabdelay = 15;
chiperasepulsewidth = 0;
chiperasepolltimeout = 10;
programfusepulsewidth = 0;
programfusepolltimeout = 5;
programlockpulsewidth = 0;
programlockpolltimeout = 5;
memory "eeprom"
size = 256;
paged = no;
page_size = 4;
min_write_delay = 4000;
max_write_delay = 4500;
readback_p1 = 0xff;
readback_p2 = 0xff;
read = "1 0 1 0 0 0 0 0 0 0 0 x x x x x",
"x a6 a5 a4 a3 a2 a1 a0 o o o o o o o o";
write = "1 1 0 0 0 0 0 0 0 0 0 x x x x x",
"x a6 a5 a4 a3 a2 a1 a0 i i i i i i i i";
loadpage_lo = " 1 1 0 0 0 0 0 1",
" 0 0 0 0 0 0 0 0",
" 0 0 0 0 0 0 a1 a0",
" i i i i i i i i";
writepage = " 1 1 0 0 0 0 1 0",
" 0 0 x x x x x x",
" x a6 a5 a4 a3 a2 0 0",
" x x x x x x x x";
mode = 0x41;
delay = 6;
blocksize = 4;
readsize = 256;
;
memory "flash"
paged = yes;
size = 4096;
page_size = 32;
num_pages = 128;
min_write_delay = 4500;
max_write_delay = 4500;
readback_p1 = 0xff;
readback_p2 = 0xff;
read_lo = " 0 0 1 0 0 0 0 0",
" 0 0 0 0 0 0 a9 a8",
" a7 a6 a5 a4 a3 a2 a1 a0",
" o o o o o o o o";
read_hi = " 0 0 1 0 1 0 0 0",
" 0 0 0 0 0 0 a9 a8",
" a7 a6 a5 a4 a3 a2 a1 a0",
" o o o o o o o o";
# The information in the data sheet of April/2004 is wrong, this works:
loadpage_lo = " 0 1 0 0 0 0 0 0",
" 0 0 0 x x x x x",
" x x x x a3 a2 a1 a0",
" i i i i i i i i";
# The information in the data sheet of April/2004 is wrong, this works:
loadpage_hi = " 0 1 0 0 1 0 0 0",
" 0 0 0 x x x x x",
" x x x x a3 a2 a1 a0",
" i i i i i i i i";
# The information in the data sheet of April/2004 is wrong, this works:
writepage = " 0 1 0 0 1 1 0 0",
" 0 0 0 0 0 0 a9 a8",
" a7 a6 a5 a4 x x x x",
" x x x x x x x x";
mode = 0x41;
delay = 6;
blocksize = 32;
readsize = 256;
;
# ATtiny2313 has Signature Bytes: 0x1E 0x91 0x0A.
memory "signature"
size = 3;
read = "0 0 1 1 0 0 0 0 0 0 0 x x x x x",
"x x x x x x a1 a0 o o o o o o o o";
;
memory "lock"
size = 1;
write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
"x x x x x x x x 1 1 i i i i i i";
read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
"x x x x x x x x x x o o o o o o";
min_write_delay = 9000;
max_write_delay = 9000;
;
memory "lfuse"
size = 1;
write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
"x x x x x x x x i i i i i i i i";
read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
"x x x x x x x x o o o o o o o o";
min_write_delay = 9000;
max_write_delay = 9000;
;
memory "hfuse"
size = 1;
write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
"x x x x x x x x i i i i i i i i";
read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
"x x x x x x x x o o o o o o o o";
min_write_delay = 9000;
max_write_delay = 9000;
;
memory "efuse"
size = 1;
write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
"x x x x x x x x x x x x x x x i";
read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
"x x x x x x x x o o o o o o o o";
min_write_delay = 9000;
max_write_delay = 9000;
;
# The Tiny2313 has calibration data for both 4 MHz and 8 MHz.
# The information in the data sheet of April/2004 is wrong, this works:
memory "calibration"
size = 2;
read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
"0 0 0 0 0 0 0 a0 o o o o o o o o";
;
;